Sharpening

Japanese Whetstones Explained: Which Grits You Actually Need

A practical guide to Japanese sharpening stones: what grit numbers mean, soaking vs splash-and-go stones, and the simplest setup for keeping a Japanese knife sharp.

Published November 17, 2026 · 8 min read

A Japanese knife is only as good as its edge, and the traditional way to keep that edge is a whetstone (in Japanese, toishi). Whetstones look intimidating, but you need far fewer of them than most shops suggest. This guide explains what to buy first and why.

Why whetstones instead of a pull-through sharpener?

Japanese knives are usually harder and thinner behind the edge than European knives. Pull-through sharpeners with carbide or ceramic wheels tend to tear at that thin, hard edge, which can cause chipping and an uneven bevel. A whetstone removes metal gradually and lets you keep the angle the maker intended. It takes a little practice, but it is the method nearly every Japanese knife maker recommends.

What grit numbers mean

Grit is roughly how fine the abrasive particles are. A lower number is coarser (removes metal faster), and a higher number is finer (polishes and refines the edge). Japanese grit numbers follow the JIS standard, so they are not always directly comparable to Western stone ratings, but the broad ranges are consistent:

Grit range Japanese name What it’s for
120–600 Arato (coarse) Repairing chips, reshaping a damaged tip, thinning
800–2000 Nakato (medium) Normal sharpening. #1000 is the workhorse
3000–8000+ Shiageto (finishing) Refining and polishing the edge for cleaner, smoother cuts

The setup most home cooks need

  • Start with a #1000 stone. It is enough to sharpen a moderately dull knife and to maintain it for months. If you buy only one stone, buy this.
  • Add a finishing stone (#3000–#6000) next. It makes the edge noticeably smoother and longer-lasting, especially on harder steels.
  • Add a coarse stone (#220–#400) only if you need it. You need it when a knife has a chip, a broken tip, or has been neglected for a long time. Many people never do.
  • Combination stones (for example #1000/#6000 on one block) are a good, affordable way to get both medium and fine in one purchase.

Soaking stones vs splash-and-go stones

  • Soaking stones must sit in water (typically around 10–15 minutes, until bubbles stop rising) before use. Many traditional and budget stones are this type. Don’t store them permanently in water unless the maker says it’s fine, and let them dry fully before putting them away.
  • Splash-and-go stones only need a splash of water on the surface. Many modern Japanese stones are made this way. They are more convenient for a quick touch-up but usually cost more. Some must not be soaked, because long soaking can crack or weaken them, so always check the maker’s instructions.

Keep your stone flat

Every stone wears into a shallow dip over time. A dished stone makes it hard to hold a consistent angle and can round off your edge. Flatten it regularly with a flattening plate or a coarse lapping stone: draw a pencil grid on the stone, rub it on the plate until the pencil lines are gone, and it’s flat again.

Well-known Japanese stone makers

You’ll see these names often. All make stones across a wide price range:

  • King (Matsunaga Stone): long-established, affordable soaking stones; a classic first stone.
  • Naniwa: wide range, including splash-and-go lines.
  • Shapton: hard, fast-cutting splash-and-go ceramic stones, popular with professionals.
  • Suehiro: broad range from entry-level to finishing stones.

Natural stones (tennen toishi) from Kyoto and elsewhere also exist. They are beautiful and prized by enthusiasts, but they vary stone to stone and are not where to start.

Accessories worth having

  • A non-slip base or stone holder so the stone doesn’t move while you sharpen.
  • A flattening plate (see above).
  • A marker pen: color the edge bevel, take a few strokes, and look at where the ink has been removed. It shows instantly whether your angle is right.

Summary

  1. Buy a #1000 stone first.
  2. Add a #3000–#6000 finishing stone when you’re comfortable.
  3. Only buy a coarse stone if you need to repair damage.
  4. Keep the stone flat, and follow the maker’s soaking instructions.

Ready to use it? Read our step-by-step guide to sharpening a Japanese knife on a whetstone.