Sharpening
How to Sharpen a Japanese Knife on a Whetstone (Beginner Steps)
A clear, step-by-step method for sharpening a double-bevel Japanese kitchen knife on a whetstone, from finding the angle to removing the burr.
Sharpening on a whetstone looks like a craft that takes years. Getting a very sharp, usable edge does not. This guide covers the basic method for a double-bevel Japanese kitchen knife, such as a gyuto, santoku, nakiri or petty. Single-bevel knives (yanagiba, deba, usuba) are sharpened differently and are not covered here.
What you need
- A medium-grit stone, around #1000 (see our whetstone guide).
- Optional: a finishing stone (#3000–#6000).
- A non-slip base or a damp cloth under the stone.
- Water, a towel, and a marker pen.
Step 1: Prepare the stone
Soak it if it’s a soaking stone (until bubbles stop rising), or splash the surface if it’s a splash-and-go stone. Place it on a non-slip base on a stable counter, with the long side pointing away from you. Keep a little water on the surface throughout. The grey slurry that forms is normal and helps sharpening, so don’t wipe it off.
Step 2: Find the angle
Most Japanese double-bevel knives are sharpened at roughly 10–15 degrees per side, lower than the 20 degrees common on many European knives. You don’t need a protractor:
- A gap under the spine of about two stacked coins is in the right range for most knives.
- Use the marker trick. Color the edge bevel, take a few light strokes, then look. If ink is removed only at the very edge, your angle is too high. If it’s removed only at the top of the bevel, it’s too low. Adjust until ink comes off the whole bevel.
Consistency matters more than the exact number. A steady 13 degrees beats a wobbly 10.
Step 3: Sharpen the first side
- Hold the handle with your dominant hand, index finger on the spine or thumb on the flat of the blade near the bolster.
- Place two or three fingers of your other hand on the blade near the edge, applying light pressure on the part touching the stone.
- Divide the blade into sections (tip, middle, heel). Working one section at a time, push the knife forward and pull it back across the stone at your angle. Apply gentle pressure mainly on the stroke toward the edge (when the edge is trailing).
- Do roughly 10–20 strokes per section, then move your fingers to the next section.
Step 4: Feel for the burr
As you remove metal, a tiny curled lip of steel called a burr (kaeri) forms on the opposite side of the edge. Carefully slide your thumb across the edge, from spine toward edge and never along it, on the side you’re not sharpening. You’ll feel a slight catch.
Don’t move on until you can feel a burr along the full length of the blade. This is the single most important step: no burr means the two bevels haven’t met yet, and the knife won’t be fully sharp.
Step 5: Sharpen the second side
Flip the knife and repeat the same process on the other side until a burr forms back on the first side. Many people do slightly fewer strokes on the second side for knives sold with a slight asymmetric edge, but for a first sharpening, equal work on both sides is fine.
Step 6: Remove the burr
Reduce the pressure to almost nothing and alternate sides with single, light strokes, a few times each side. Then:
- If you have a finishing stone, repeat the process there with lighter pressure and fewer strokes. The edge will become smoother and more polished.
- Finally, gently draw the edge through a piece of cork or soft wood, or across folded newspaper, to remove any remaining burr.
Step 7: Test, clean and dry
Test by slicing a sheet of paper or a tomato. A sharp knife glides through without tearing. Rinse and dry the knife completely, rinse the stone, and let it dry before storing.
Common mistakes
- Rocking the angle. Keep your wrists locked and move from the shoulders.
- Too much pressure. Let the stone do the work, especially on hard steel.
- Skipping the burr check. This causes most “it’s still not sharp” problems.
- Sharpening on a dished stone. Flatten it regularly.
How often?
For a home cook, a full sharpening every one to three months is typical, depending on use and steel. Between sharpenings, a few light strokes on a fine stone, or a ceramic honing rod used gently, keeps the edge going. Avoid grooved steel honing rods on very hard Japanese knives, as they can chip the edge.
New to Japanese knives? Start with which knife to buy first and how knife steels differ.